which ball valve - high pressure or low pressure?
Asked on: 29 Jul 2005
Hello,
Should I purchase a ball valve marked 'high pressure' or one that is
marked 'low pressure'? It's for the water tank in the loft fed by the
rising main.
Hope I make sense
Wayne.
www.diybanter.com/showthread.php?t=115546&mode... - At least 3 Posts
- Only this forum
Low-pressure to high-pressure?
Asked on: 07 Nov 2008
I understand sometimes a headache can change from low-pressure to high-pressure after surgical repair of the dura. Does anyone know if it is possible for this to happen during the natural healing process of the dura?
I'm assuming that after a sudden seal of the dura, the body is so used to over-producing csf that when the hole is closed up and there is no longer a leak, the pressure can build and cause a high-pressure headache. I wouldn't assume the same would be true in the case of the body clo...
brain.hastypastry.net/forums/showthread.php?t=... - At least 10 Posts and 8 Authors
- Only this forum
High oil pressure or crank case pressure or both?
Asked on: 29 Dec 2008
OK, my car is finally running but its leaking oil. Or, IMO, oil pushing past seals and gaskets. One problem area is the valve cover in the spark plug area. Its actually getting in the spark plug wells and also pooling on the valve cover itself. The valve cover gasket has been replaced (more than once). Its also leaking from somewhere else but I haven't had a chance to pinpoint it yet. I'm thinking rear main seal as its dripping off the transfer case.
I don't have an oil pressure gauge other than...
www.gadsm.org/showthread.php?t=34484&mode=line... - At least 13 Posts and 6 Authors
- Only this forum
pre-set air pressure?
Asked on: 15 Aug 2007
is it better to get a tank thats fixed for low pressure or high pressure?
www.paintballguns.net/forum/showthread.php?t=5... - At least 13 Posts and 2 Authors
- Only this forum
Pressure Pump - pressure switch setting?
Asked on: 04 Jan 2006
I have a Grundfos CH2-30 pressure pump and no instruction manual and the Grundfos website is of no help. Got someone in to adjust the pressure switch when I wasn't at home so I was unable to watch over their shoulder and thereby avoid paying them to come next time it needs adjusting.
Can anyone help with how you set the pressure switch limits. ie what dial does what with the pressure switch?
Allan.
www.woodworkforums.com/showthread.php?t=25249&... - At least 5 Posts and 2 Authors
- Only this forum
Pressure for pressure bleeding brakes?
Asked on: 22 Nov 2008
Does anyone have any guess as to the pressure used to power-bleed Neon brakes (Non-ABS)? I'm GUESSING about 15-20, but not quite sure.
Thanks!
Mark
forums.neons.org/viewtopic.php?f=1&t=330109 - At least 5 Posts
- Only this forum
consiglio su scelta pettorina: 661 pressure suit o pro pressure suit?
Asked on: 25 Nov 2008
Hola ragazzi, vorrei prendermi una pettorina e sono indeciso su queste 2:
661 pressure suit e 661 pro pressure suit. Io propenderei per la prima ma ieri il mio caro amico Leo mi ha fatto notare la seconda..hehe
sono sempre invogliato dalla prima, ma magari qualcuno ne ha una o le ha provate e sa dirmi qualcosa di più =)
eccole, la prima è la pressure, la seconda la pro pressure:
grassie ;)
www.bike-board.net/community/forum/showthread.... - At least 3 Posts and 2 Authors
- Only this forum
lazy oil pressure - aprox. time for oil pressure to build up?
Asked on: 02 Jan 2009
Hi all,
we have around 14° F over here and my trucks engine (318, Carter BBD, 15W40 Castrol Oil, mileage unknown) did make some "scary" "klunk-klunk-klunk" noise this morning for about 5 seconds.
Sounded like shot rod bearings but the noise disappeared after 5 seconds as described.
This leads me to the question, how long it should take the engine to build up oil-pressure?
Or better: how long should it take the original oil pressure gauge to show oil pressure?
(Sometime oil-pressure drops to none...
ramchargercentral.com/index.php?topic=116598 - At least 5 Posts and 5 Authors
- Only this forum
|
About Omgili Q&A
Omgili Q&A is a sub-section of Omgili that is dedicated to finding questions and answers.
Most of the questions you want answered have been asked before, and many of them have been answered. Omgili Q&A looks in discussion groups, forums, Q&A sites and extracts the answers for your queries.
It's simple, fast and efficient.
|
Omgili Home